HITACHI
is HITACHI’s On Screen Display function for easy operation.
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP THIS USER MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your
monitor.
.
The serial number is located on the rear of the monitor.
This monitor is
compliant when used with a computer
equipped with VESA DPMS.
The ENERGY STAR@ emblem does not represent EPA endorsement
of any product or service.
As an ENERGY STAR@ Partner,
product meets the ENERGY
has determined that this
guidelines for energy efficiency.
NOTE:
The manufacturer assumes no
The information in this manual is subject to change without notice.
responsibility for any errors that may appear in this manual.
VGA is a registered trademark of International Business Machines Corporation.
VESA is a trademark of a nonprofit Video Electronics Standard Association
is a trademark of Environmental Protection Agency (EPA).
REMARQUE:
Les informations
Le constructeur
dans ce manuel peuvent
modifiees
preavis.
n’accepte aucune responsabilitb pour les erreurs qui peuvent eventuellement apparaitre dans ce
manuel.
VGA est une marque
VESA est la marque
d’ International Business Machines
organisation but lucratif. la Video Electronics Standard Association.
est une marque de I’ EPA (Environmental
HINWEIS:
Anderungen der Daten in dieser Bedienungsanleitung sind vorbehalten. Der Hersteller
keine Haftung jegliche in Handbuch eventuell enthaltenen
VGA ist ein eingetragenes Warenzeichen der International Business Machines Corporation.
VESA ist ein Warenzeichen der Video Electronics Standard Association, einer Organisation ohne
Erwerbscharakter.
ist ein Warenzeichen der Environmental Protection Agency (EPA).
La
contenida en este manual
sujeta a cambios sin previo aviso. El fabricante no
se responsabiliza de
que puedan aparecer en este manual.
VGA es una
VESA es una
Association.
es una
registrada de International Business Machines Corporation.
registrada de una sin de Video Electronics Standard
de Environmental Protection Agency (EPA).
Tutte le informazioni di
costruttore non si assume responsabilita’ per
manuale
soggette ad essere modificate senza preavviso. II
possono essere riportati manuale.
VGA e’
marchio di fabbrica regisrato da International Business Machine Corporation.
VESA e’
marchio di riconoscimento
organizzazione a non-profitto, Video Electronics
Standard Association.
e’ marchio di fabbrica
Eviromental Protection Agency (EPA).
Below you will
a brief summary of the environmental requirements met by this product. The
complete environmental criteria document may be ordered from:
TCO Development
SE- 114 94 Stockholm, Sweden
Fax:
8 782 92 07
(Internet):
Current information regarding
approved and
products may also be
obtained via the Internet, using the address:
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their
purpose is to prevent, or at least to delay the spread of Up to 30% of the plastic in a computer casing
can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those
flame retardants are chemically related to another group of environmental toxins, Both the flame
retardants containing bromine or chloride and the are suspected of giving rise to severe health
effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*
processes. Flame retardants have been found in human blood and researchers fear that disturbances in
foetus development may occur.
The relevant
demand requires that plastic components weighing more than
grams must not
contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in
the printed circuit boards since no substitutes are available.
Cadmium*’
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer
displays. Cadmium damages the nervous system and is toxic in high doses. The relevant
requirement states that batteries, the colour-generating layers of display screens and the electrical or
electronics components must not contain any cadmium.
Mercury”
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is
toxic in high doses. The relevant
It also demands that mercury is not present in any of the electrical or electronics components associated
with the unit.
requirement states that batteries may not contain any mercury.
(freons)
The relevant
manufacture and assembly
boards. break down ozone and thereby damage the ozone layer in the stratosphere, causing
requirement states that neither
nor
may be used during the
product. (freons) are sometimes used for washing printed circuit
increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant
melanoma) as a consequence.
Lead”
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning. The relevant TC0’99 requirement permits the
inclusion of lead since no replacement has yet been developed.
l
defined
substances which accumulate within living organisms
Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative
I - 1
1-2
......................................................................................................
.....................................................................................................
FEATURES
CAUTIONS
l - 6
..............................................................................................
INSTALLATION
STANDARD SETTINGS..
...............................................................................
1
7
l - 8
.......................................................................................
OPERATION.. ..........
...................................................................
AUTOMATIC SIGNAL CHECK..
POWER MANAGEMENT SYSTEM..
............................................................
.............................................................................................
PLUG PLAY..
1
11
. .
...................................................................................
SPECIFICATIONS..
.
The following features are provided by the Colour Monitor.
Sharpest Focus and Highest Contrast
Flat screen Enhanced Dot Pitch (EDP) CRT with FS double focus and AR-ASC coating
gives the sharpest focus and highest contrast to minimise eye fatigue.
Wide-range Multi-Scanning
Automatic scanning and automatic adjustment to conform with a wide range of scanning
frequencies and user requirements.
Digital Picture Control Function
Position, size, pincushion, trapezoid, parallelogram, pin balance and rotation are
adjustable by digital controls.
Geometry setting can be stored for different
frequencies. Microprocessor-based
preset functions can store 26 sets of geometry settings including the standard factory
settings.
Digital Colour Control Function
Red, green, and blue colour balance is adjustable by digital control.
An adjusted colour setting can be stored and recalled by the colour select button.
Moire Reduction
This monitor has horizontal and vertical moire reduction function.
Power Saving System
The Environmental Protection Agency (EPA) has established a voluntary program by
which manufacturers enable computer products to go into low power states while not
being used. This monitor has a low power “sleep” mode, which is compliant with the EPA
requirements for the
program, and will assist you in conserving energy.
Please refer to the section of “POWER SAVING SYSTEM” for details.
An On Screen Display function that allows direct access to
adjust all operations from the front panel.
PLUG
This monitor is VESA
computer compliant with VESA DDC (Display Data Channel).
PLAY
compliant when used with a
l - l
n
NEVER REMOVE THE REAR COVER !
__ The rear cover MUST be removed only by authorised service personnel. This
monitor contains high voltage components.
n
THE POWER POINT SHOULD BE CLOSE TO THE MONITOR AND
EASILY ACCESSIBLE !
INSTALL THE UNIT IN AN SUITABLE ENVIRONMENT !
DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard.
n
This unit is designed to be used in an office or business environment.
the unit to vibrations, dust, or corrosive gases.
DO NOT subject
q
KEEP IN A WELL VENTILATED PLACE !
DO NOT cover this monitor or place anything against any sides (not only the top, right
and left side but also the rear and bottom side) of unit. Ventilation holes are provided at
all sides of the rear cover to prevent the temperature from rising.
n
KEEP AWAY FROM HEAT SOURCES !
AVOID placing the unit in direct sunshine or near a heating appliance.
BE CAREFUL OF MAGNETIC FIELDS !
n
DO NOT place a magnet, loudspeaker system, floppy disk drive, printer, or anything
which will generate magnetism near the unit. A magnetic field may cause blurred
or distortion of the displayed pattern.
n
BE CAREFUL OF GENERATED MAGNETISM !
After the power has been turned on or “DEGAUSS” button has been pressed, the CRT is
demagnetised for approximately 10 seconds. This generates a strong magnetic field around the
front cover which may affect the data stored on magnetic tape or disks near the front cover.
Place such magnetic recording equipment and tapes/disks away from this unit.
AMBIENT ILLUMINATION
Avoid direct rays of the sun or room lighting onto the CRT screen in order to prevent eye fatigue.
n
THE ENCLOSED POWER CORD MUST BE USED !
In Europe, a proper European standard approved power cord is to be used with this
monitor. For a rated current up to 6 A, a type not lighter than 3G 0.75
3G 0.75 must be used.
or
In USA/Canada, use a UL
or CERTIFIED power cord set
meeting the following specifications
Rating: min.
7A
Length: max. 3.0 m
Type: SVT or SJT
Plug type: NEMA
5P figure, Parallel blade, Grounding type
Failure to do so may cause fire or electric shock hazard.
USE ONLY THE CORRECT VOLTAGE POWER OUTLET WITH SAFETY
GROUND CONNECTION !
100 120 V for USA, Canada, etc.
200 240 V for Europe, etc.
(This monitor will automatically adjust to the input voltage 100 240V.)
1 - 2
n
CAUTION for 200 240V operation only
This equipment relies on the protective devices in the building installation for short-circuit
and over-current protection. Refer to the following table for the suitable number and
location of the protective devices which should be provided in the building installation.
.
PROTECTIVE DEVICES IN SINGLE PHASE EQUIPMENT OR SUB -ASSEMBLIES
Minimum number
of fuses or circuit
breaker poles
Location
Protection
against
Both conductors
Either of the two
conductors
Equipment to be connected to Earth faults
POWER SYSTEMS with earthed Over-current
neutral reliably identified
Both conductors
Either of the two
conductors
Earth faults
Over-current
Equipment to be connected to
any supply, including IT
POWER SYSTEMS and
supplies with reversible plugs
Verify that the protective devices in the building installation meets the conditions in the
table prior to installing the equipment.
n
BE CAREFUL OF POWER CORD CONNECTION !
Before inserting the plug of the power cord into a power point of the correct voltage,
Then, insert
check that the connection portion of the power cord is clean (with no dust).
the plug of power cord to a power point firmly, otherwise it may cause electrical shock or
fire.
REMOVE THE POWER CORD FOR COMPLETE SEPARATION !
For complete separation from the power source, remove the power cord from the monitor
or from the wall outlet.
n
AVOID FREQUENT POWER ON-OFF SWITCHING !
It may cause blurred
or
DO NOT repeat OFF and ON in a short period.
distortion of the displayed pattern.
n
BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE !
To prevent electrical shock by the static electricity on the CRT surface, disconnect the
power cord at least 30 seconds after turning off the power.
n
ABOUT CLEANING
This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen.
Use water or alcoholic solvent with soft cloth like gauze to clean the surface of the
screen.
NEVER use abrasive, glass cleaner containing highly concentrated ammonia and strong
base chemicals since they damage the surface treatment.
Clean the cabinet and controls with a lightly moistened soft cloth.
DO NOT use aerosol sprays, solvents or abrasive cleaners.
l - 3
FCC (Federal Communications Commission) STATEMENT WARNING
WARNING : This equipment has been tested and found to comply with the limits for a
These limits are designed
Class B digital device, pursuant to Part 15 of the FCC Rules.
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur
If this equipment does cause harmful interference to radio or
in a particular installation.
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Instructions to Users : This equipment complies with the requirements of FCC (Federal
Communication Commission) equipments provided that following conditions are met.
(1) Power cord: Unshielded power cord must be used.
(2) Video inputs: The input signal amplitude must not exceed the specified level.
CAUTION : Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Nissei
200
U.S.A.
America, Ltd.
Located at:
02090-1124
Brook Drive Suite 2200, Westwood. MA.
Tradename:
Model
Color
USB HUB)
DUB-01
Satoshi
November
MA. , U. s .A.
n
FOR THE CUSTOMERS IN THE U.K.
THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND
EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.
IMPORTANT FOR UNITED KINGDOM
WORDING FOR CLASS I EQUIPMENT INSTRUCTION BOOKS AND LABELS
is supplied with a moulded plug incorporating a fuse,
The mains lead on this equipment
Should the fuse need to be
the value of which is indicated on the pin face of the plug.
replaced, an ASTA or BSI approved BS 1362 fuse must be used of
the fuse cover is detachable never use the plug with the cover omitted.
If
the same rating.
If a replacement
fuse cover is required, ensure it is of the same
as that visible on the pin face of the
plug. Fuse covers are available from your dealer.
If the plug fitted is not suitable for
DO NOT cut off the mains plug from this equipment.
the power points in your home or the cable is too short to reach a power point, then
obtain an appropriate safety approved extension lead or consult your dealer.
Should it be necessary to change the mains plugs, this must be carried out by a
competent person, preferably a qualified electrician.
If there is no alternative to cutting off the mains plug, ensure that you dispose of it
immediately, having first removed the fuse, to avoid a possible shock hazard by
inadvertent connection to the mains supply.
WARNING: THIS EQUIPMENT MUST BE EARTHED
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:
Green Yellow
to Earth
Brown to Live
Fuse
Blue to Neutral
Cord Clamp
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
As these
may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in
the plug which is marked with the letter E or by the earth symbol
or coloured GREEN
or GREEN and YELLOW.
The wire coloured BLUE must be connected to the terminal marked with the letter N or
coloured BLUE or BLACK. The wire coloured BROWN must be connected to the
terminal marked with the letter L or coloured BROWN or RED.
Install the monitor in the following way, taking care to maintain safety
REAR VIEW
FRONT VIEW
Rear Cover
Signal Input
Connector
AC Inlet
Control Panel
Power Cord
Tilt Swivel Base
to the host computer
USB Slot
(for the optional USB HUB Module)
to a receptacle of
the correct voltage
1. Installation
Install the monitor on a horizontal base.
2. Power Cord Connection
Make sure of using the power cord meeting the safety standard of the country in
which you are using the monitor.
Insert the connector of a power cord to the AC Inlet of the monitor.
Insert the plug of the power cord to a power point of the correct voltage.
3. Signal Cable Connection
Insert the Signal Input Connector of the monitor to the host computer, with attention to
it’s suitability, and secure the screws on the connector shell firmly.
D-Sub Mini 1 B-pin Connector
Pin No.
Signal
1
Red Video
11
Ground
12
13
14
15
Bi-directional Data [SDA]
(or
4. Power On
Turn on the Power Switch of the
monitor first, then the computer.
Refer to Page 1-8 “POWER ON/OFF”.
Data Clock [SCL]
l - 6
Microprocessor-based preset functions can store 26 sets of geometry settings including
the standard settings. The following industrial standard settings have been
programmed by the factory.
Horizontal
Frequency
Video Mode
No.
Video Mode Name
(with Resolution and Vertical Frequency)
31.47
37.86
53.67
60.02
68.68
67.50
VGA
640
70 Hz
85 Hz
85 Hz
75 Hz
1
VGA
2 VESA 640
3 VESA 800
VESA
VESA
VESA
VESA
X
4
5
6
VESA 1024
VESA 1024
VESA 1152
85 Hz
75 Hz
NOTE :
n
Input signals with approximately the same frequencies may be regarded as the same
signal.
n
The following horizontal timing conditions are recommended (at sync. H, V
separate or H/V composite).
for 31
45
horizontal frequency:
Horizontal front porch should be more than 0.1
Horizontal sync. width should be within 1
3.8
Horizontal back porch should be more than 1.2
Horizontal blanking width should be more than 3.5
for 45
69
horizontal frequency:
Horizontal front porch should be more than 0.1
Horizontal sync. width should be within 1 .O 3.0
Horizontal back porch should be more than 1
Horizontal blanking width should be more than 3.0
n
The following vertical timing conditions are recommended.
Vertical front porch should be more than 10
Vertical sync. width should be less than 200
Vertical back porch should be more than 400
Vertical blanking width should be more than 500
n
n
In case the front or back porch is extremely long, or the data display time is
extremely short, it may not be able to set the expected size and position.
Standard settings are subject to change without notice.
l - 7
Power LED
Power Switch
Switches Switches
Switch
POWER
Press the Power switch, to switch the power ON or OFF.
n
n
When power is ON, the power LED lights.
After turning OFF the switch, wait at least 5 seconds before restarting the monitor.
Otherwise the monitor may operate incorrectly.
If the picture doesn’t appear, turn OFF the power switch, make sure of the following
and wait at least 30 seconds before restarting the monitor.
Make sure the power switch of the computer, power cord connection, signal cable
connection and the input sync. signal are correct.
CONTROL
Press the Status switch. The On Screen Display function of
then shows
the selected function, its condition, the function menu and the input signal
frequencies.
n
You can select the
language.
Use the function “LANGUAGE SELECT”.
To select the function, use the Function
switches.
To execute the selected function, use the
Adjust Switches in the Table-l overleaf.
...
Sample of
n
n
You can save the your geometry and
settings. Refer to “SAVE” below.
To clear the
either push the status
switch again or wait for 10 seconds.
SAVE
If the function “AUTO SAVE” is ON, you can save automatically at clearing the
l - 8
Table-l
Function
+
PINCUSHION
PIN BALANCE
recalls the factory preset modes.
When the Green reaches
When the Blue or Red the upper limit, it makes the
reaches the upper limit, it Blue and Red weaker.
make the Green weaker.
B makes the Red and Green makes the Blue stronger.
stronger.
When the Blue reaches the
When the Red or Green upper limit, it makes the
reaches the upper limit, it Red and Green weaker.
make the Blue weaker.
l - 9
Table-l (continued)
Function
+
makes the operation of makes the operation
horizontal moire circuit horizontal moire circuit
weaker.
stronger.
makes the operation of makes the operation
vertical moire circuit weaker. vertical moire circuit stronger.
LANGUAGE
changes the
language to the previous language to the next
changes the
mode.
mode.
(French)
ENGLISH
1
ITALIAN0 (Italian)
DEUTSCH (German)
ESPANOL (Spanish)
ITALIAN0 (Italian)
(French)
1
ESPANOL (Spanish)
1
DEUTSCH (German)
1
ENGLISH
POWER
MANAGEMENT
disables (OFF) the Power enables (ON) the Power
Saving System.
Saving Systems.
Refer to Page l-l 1
Refer to Page l-l 1
“POWER MANAGEMENT “POWER MANAGEMENT
SYSTEM”
disables (OFF) the Auto enables (ON) the Auto
SYSTEM”.
AUTO SAVE
DEGAUSS
Save function.
Refer to Page l-8
“SAVE”.
Save function.
Refer to Page l-8
“SAVE”.
degauss.
Use this function only when you see
impurities
on the screen after turning ON the monitor.
Wait for about 10 minutes before repeating the function.
Remember, the monitor is automatically degaussed
during initial power on.
EXIT
quits the functions of
When the monitor has detected the change of the signal input condition, the monitor will
indicate the condition automatically, as follows.
the horizontal frequency
Precision frequency,
Horizontal
mode. Refer to
MANAGEMENT
SYSTEM” below.
This monitor meets the
standard specifications.
VESA DPMS (Display Power Management Signalling)
The monitor has a built-in power management system that
automatically reduces power consumption when the PC is not in use. This power management
system is effective only when used with VESA DPMS compliant PC or Video Card.
Power Consumption Power LED
APM State Signal Requirement Monitor Action
max.
15W max.
3W max.
Orange
Orange
Orange
H.Sync. OFF
OFF
H.Sync. OFF and
V.Sync. OFF
Standby
Suspend
Off
Switches to
saving mode
screen darkens
NOTE : Once the monitor receives the first signal from the PC and initiate the power
management system.
Plug
Play is a system
It works when
This monitor complies with VESA DDC
specifications.
with computer, peripherals (including monitors), and operating system.
the monitor is connected to DDC ready computer that is running an operating system
software that is capable for the plug play.
17 inch picture tube,
0.22 mm horizontal dot pitch
C R T
(0.21 mm horizontal mask pitch)
deflection, FS double focus, AR-ASC coating.
: 0.7 Vp-p, analogue
: Separate
Video
Sync.
input Signal
level
Composite H/V, TTL level
Horizontal : 31 69
:
Vertical
Horizontal : 1280 dots (max.)
Vertical : 1024 lines (max.)
Resolution
110 MHz (typical)
16.0 inches
Video Clock frequency
Image Size
diagonal (typical)
Horizontal : 326 mm (typical)
Image Area
Vertical
: 245 mm (typical)
: Standard colour balance, 9300K
: Standard colour balance, 6500K
: User defined
9300K
6500K
USER
Colour Temperature
30 minutes to reach optimum performance level.
Warm-up Time
Power Supply
AC 100 240 V (automatically selected)
Hz, 2.5 A (max.)
Power Consumption : 110 W (typical)
(provided with power save circuit.)
412 (W) X 431 (H)
(including Tilt & Swivel Base)
373 (D) mm
Dimensions
Weight
17.0 kg (approx.)
(including Tilt Swivel Base)
Storaoe
-20°C to
10% to 90%
Operation
Environmental
Condition
to
Temperature
Humidity
10% to 80%
USB HUB Module
with 4 downstream and 1 upstream ports
USB HUB (optional)
Specification and Design are subject to change without notice.
1-12
|
Haier HTAR21 User Manual
Frigidaire FFGC2605LW User Manual
EVGA 132 GT E768 User Manual
Envision Peripherals Envision EN 5100e EN 5100E User Manual
Electrolux Thermaline WLXWCFOOOO User Manual
Electrolux Thermaline WLXWAAOOOO User Manual
Dell Professional P190S User Manual
Dacor Cooktop IWD24 User Manual
Crosley Radio CR56 User Manual
Asus A7N8X LA User Manual