FWV460
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Icemaker
Display
Control Panel
Water Nozzle
Ice Drawer
Water Tray
Drip Tray
Icemaker control panel
ON OFF
1
2
3
4
5
6
1. On button
2. Off button
3. Water glass button – this button dispenses a small amount of water.
4. Water jug button – this button dispenses a large amount of water.
5. Manual water button – this button dispenses water as long as the button is pressed.
6. Maintenance button – this button allows the icemaker to automatically empty the pipes.
The Icemaker
Before first use:
1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you.
2. Fill the water tank (even if the appliance is to be plumbed in to the mains water supply).
3. Turn on the machine at the switch on the left side of the machine.
4. Push the machine back into the housing.
5. Switch on the machine by pressing the ON button.
6
The machine is now ready for use and the display shows ICE ON WATER READY.
The water tank
It is possible to use the appliance without connecting it to the mains water supply. There is an integral water tank which
can be used in this instance. To ensure the best results from your appliance, it is recommended that the water tank be
emptied frequently and refilled with fresh water, and no water be left in the tank for long periods.
When the water tank is empty, the message WATER MISSING will show on the display.
To fill the water tank:
1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you.
2. Open the lid of the water tank and fill it until the water is 4cm from the top level. Then close the lid.
3. Push the machine back into the housing.
Please note:
You should follow the steps below in order to remove any impurities from the system and ensure best performance
from your ice maker. Failure to carry out this simple procedure could cause problems or damage to the workings of the
icemaker.
1. Turn off the mains water supply, if applicable
2. Use a sterilising solution such as Milton fluid to clean the removable ice drawer and the ice drawer housing. Follow
the instructions supplied with the sterilising solution to ensure the ice drawer is thoroughly cleaned.
3. Fill the internal water tank with 2.5l of water then add a spoonful of bicarbonate of soda to the water.
4. Use the water empty function (press and hold and , then press
before emptying the water tank by
holding ) to flush the system through with the bicarbonate solution from the water tank.
5. Repeat steps 3 and 4.
6. Fill the water tank with 2.5l of water
7. Use the water empty function (press and hold and , then press
) to clear out any bicarbonate solution remaining.
before emptying the water tank by holding
8. Repeat steps 6 and 7.
9. Turn the ice maker off
10. Turn the mains water supply back on, if applicable, or fill the water tank.
11. Turn the ice maker on. Normal operation will resume.
The Icemaker
Bicarbonate of soda is a safe compound and poses no risk to health. It is commonly available and is sold in all
supermarkets.
You should only use cold drinking water in this appliance, with water hardness level less than 7 F.
˚
The water tank can be removed for cleaning, following the steps above, and then lifting it out of the machine.
The water storage tray is located below the ice drawer. In normal use this fills with water, which is chilled and ready for
dispensing; this does not constitute a fault.
The Icemaker
To make ice
The icemaker will make ice automatically once it is switched on and will continue to make ice until the ice compartment
is full. Whenever ice is removed, the icemaker will make more ice until the compartment is full again.
To dispense water
The amount of water dispensed from the water nozzle is controlled by three different buttons.
– water glass
– water jug
– manual setting – this button dispenses water as long as the button is pressed.
The water nozzle is height adjustable for ease of use. To adjust the height, hold the black outer section of the water
nozzle and raise or lower it to the height required. The nozzle will automatically remain at the height set.
To change the preset buttons
It is possible to adjust the amount of water dispensed by the preset buttons (
&
). To do so, place a glass or jug
under the water nozzle and press button 5 until the required amount has been dispensed. Then confirm the setting by
pressing buttons
&
for the water glass button or buttons
&
for the water jug button.
Please note:
To stop water dispensing once a preset button has been pressed, simply press the button again.
To dispense ice
When the ice drawer is full, the display shows ICE FULL WATER READY.
Open the drawer fully and use the scoop provided to remove the ice as required.
Please note:
To ensure the ice is fresh, we recommend you empty the ice drawer every 6-8 hours.
If the ice drawer is not emptied for a long period of time, the appliance will go on standby for approximately ten
minutes, and the display shows ICE OFF WATER READY. After the standby period has ended, the appliance will begin
to make ice again. If you do not want to wait for the standby period to finish, press the ON button.
Care and maintenance
Always disconnect the appliance from the power before any cleaning or maintenance.
As the icemaker has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner
(including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively
cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth.
Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team
for cleaning stainless steel surfaces.
You should remove and clean regularly the water tank, the ice compartment drawer and both sections of the drip tray.
Once cleaning is complete, reconnect the mains power supply.
If the appliance is not to be used for prolonged periods of time, you should empty, clean thoroughly and unplug the
appliance.
To empty the icemaker, follow the steps below:
1. Press and hold button and together and then press button
. This will empty the water in the
icemaker’s internal system. The display will show ICE OFF WATER EMPTY to confirm the icemaker’s internal
system is empty.
2. Empty the ice from the ice compartment.
3. Place a jug under the water nozzle and press button until no more water is dispensed.
4. To make sure the pipework is completely empty, you should unscrew the cap at the back, using a cup to catch
the last of the water.
IMPORTANT:
Steam cleaners must not be used when cleaning this appliance.
Ensure that all parts are correctly replaced after cleaning before attempting to use the icemaker.
Troubleshooting
Problem
Solution:
WATER MISSING shows in the display
The water tank is empty and needs to be refilled
ICE FAULT WATER READY shows in the display
at first switch on
Turn the icemaker off with
switching it on again.
and the main switch on the side, before
The icemaker emits a continuous beep
The dispensed water has an unpleasant taste
ICE FAULT shows in the display
UV Sterilizer needs replacing - contact CDA Customer Care
Ensure that only water pipes suitable for drinking water are used
Turn the icemaker off with
remove some ice and turn it on again.
We recommend that the unit is not left on permanently.
IMPORTANT:
Do not operate with a damaged cord, plug, after the appliance malfunctions or has been damaged in any way. You should
contact CDA Customer care for inspection, repair or adjustment.
min. 200cm2
Installation
IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY
600
QUALIFIED PERSON.
450 min
392.5
560
1. Slide the base unit into the housing ensuring the dimensions are
correct as per figure 1.
450 min
19
492.5
2. Fix the base unit in place by attaching the 10 screws in to the holes as
shown in figure 2 and figure 3. If the sides of the base are not
flush with the sides of the housing, then use the shims provided.
458
436
440
3. Push the runners fully closed on the base unit.
595
4. Connect the plug to the plug socket. This must be accessible after
the appliance has been installed.
min. 200cm2
fig. 1
5. Using an appropriate supply pipe, connect one end of the hose
to the threaded inlet of the valve on the
dispenser, located at the rear of the appliance.
6. Insert the flow restrictor between two rubber washers, then connect
the other end of the pipe to the mains water supply
(drinking water only)
7. Insert the appliance into the housing, ensuring that the runners on
the machine are located in the runners on the base unit. Then slide
the appliance fully into the housing.
fig. 2
fig. 3
ꢀ
Installation
If necessary the included 6 metre water hose can be cut down to the required
length using a sharp knife. You should ensure no burrs are left on the hose.
The water connection fitting and flow reducer are prefitted However, if you
should need to reconnect the fitting, proceed as follows:
Connect one push fit tap adaptor to each end of the water hose.
fig. 4
Insert the supplied flow restrictor and black o-ring into the tap adaptor as per
fig 6. (Please note, the flow restrictor should be fitted to the tap adaptor that
is to be fitted to the water supply tap)
Secure the tap adaptor that does not contain the flow restrictor to the valve
on the back of the appliance and then connect the remaining tap adaptor to
the mains water supply tap.
Once both tap adaptors are securely fitted turn on the water supply and
check for leaks.
i
Flow restrictor
fig. 5
Please note:
Due to the weight of this appliance, the housing unit must be secured to the
wall prior to installation.
You must ensure that all water connections are sound and check there are no
leaks before completing installation.
For best performance, the mains water pressure must be between 0.1 - 3 bar.
Do not use outdoors.
Do not install near a hob or oven.
To reduce the risk of electric shock, do not mount over a sink.
fig. 6
Electrical information
Warning! This appliance must be earthed.
Green & Yellow to Earth
Brown to
Live
A
13 Amp
Fuse
B
Cord
Clamp
Blue to Neutral
The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug,
follow the steps below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid the risk of
electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:-
•
•
•
The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or
by the Earth symbol or coloured GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or
coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or
coloured RED or BROWN.
If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the
supply cable, the appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible place.
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
|